A2200, Archer C6U, TL-WR1043N( V5 ), Archer C80, Archer AXE95, Archer C8, Archer AX10000, Archer C3150, Archer C9, Archer AX50, Archer C6, Archer C7, Archer AX90, Archer AX6000, Archer C5400X, Archer C25, Archer C24. If you need any help, check out our tutorial on how to find your router's IP address. How to configure IPTV function on wireless router. If that is the case, review our IP address router list, and find the right address. In this case, your network is most certainly using a different IP address. TP-Link Archer C9 Product Details Supports 802.11ac standard-the next generation of Wi-Fi Simultaneous 2.4GHz 600Mbps and 5GHz 1300Mbps connections for 1.9. In many cases problems related to loading the login screen of the router are related to it having a different IP from the one tried to be loaded.You can also lookup what exact IP address has been set as default for the router. Router login page not loading? If for some reason the admin webpage fails to load, then check if the device you are using is connected to the wi-fi.Doing so will reset your router to the factory settings. In order to do this, press and hold the small black button usually situated at the back your router case for approximately 10 seconds. Forgot Login Password? Try the hard reset function.Do not forget to store the login details after you have reset them. If you experience problems logging in a Archer C9 v2.x router, then you are probably using the wrong username or password. If you do not happen to know what the username and password is then feel free to lookup some of the default ones for Archer C9 v2.x routers by TP-LINK. Now enter the default username and password of your router and you will be granted access to its admin panel. That will prevent you from losing connection in the middle of the configuration / setup process.īy using a web browser of your choice and entering the IP address of your Archer C9 v2.x router in the address bar you will load the login screen. You can find the ip address on the back of your router. Suggestion - It is recommended for the connection to be done by using a cable attached to the TP-LINK Archer C9 v2.x router. To Login as Admin at TP-LINK Archer C9 v2.x Router use the guide below.Ĭonnect your PC or Laptop via cable to your router. Default logins for TP-LINK 100 % IP Address: 192.168.0.1 Username: admin Password: admin TP-LINK Archer C9 v2.x Router Login You should be redirected to your router admin interface. Secondly, turn it upside down and find the. Lastly, disable the DHCP server, as the DHCP settings will be received from the main routerĦ.TP-LINK - Archer C9 v2.x Router Login - Username, Password and IP Address Router Model: Archer C9 v2.xīased on your local ip address, pick the correct IP address from the list above and click Admin. Default Router Password and Wi-Fi Password TP-LINK Archer C9 First step, you need to is get access to the router. Now, enter the MAC Address of the LAN part to be bridged of the Archer C9 (can be found under 'Network - LAN')Ĥ. Under '2.4Ghz Wireless', click 'Enable WDS Bridging' Go to 'System Tools - System Parameters' Now, we need to bridge the LAN to your Wireless SSID Set-up the Wireless Connections and SSIDģ. Enter the subnet mask identically as the subnet mask within the LAN (e.g. Enter the IP address manually within the subnet of the main router (e.g. Set-up the Archer C9 as an Access Point manually If you need some of the Router Mode Options, the key is to enable a WDS Bridge to the Ethernet MAC Address of the Router, since the wired clients do get a fully working connection.ġ. If you are OK with having different SSIDs and do not need the extra Router Mode Options, you can easily run the Archer C9 in Access Point Mode - Done.ī. The combination 'same SSID' - 'Access Point Mode' + clients always choosing the right Access Point is not guaranteed, since in my set-up, I had MAC filtered clients from AP B and C which always need to connect to AP A.Ī. 'Access Point Mode' does not allow 'Router Mode' options (such as NAT, QoS, MAC Filtering. For AP C (the C9), the exact same setting did not work - the wired clients have LAN/WAN access, the wireless clients only have LAN access. For AP A and B (both C8), the settings work fine by disabling the DHCP and connecting through Lan Port 1 Access Point C (TP-Link Archer C9) - Static LAN 192.168.0.4 - DHCP Disabled - Connected through Ethernet LAN Port 1 Access Point B (TP-Link Archer C8) - Static LAN 192.168.0.3 - DHCP Disabled - Connected through Ethernet LAN Port 1 Access Point A (TP-Link Archer C8) - Static LAN 192.168.0.2 - DHCP Disabled - Connected through Ethernet LAN Port 1 ISP Modem (LAN 192.168.0.1) - Ethernet LAN Port 1 to Hereby, I want to share a solution for an issue I had with my new Archer C9.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |